How to Remove and Also Replace a Bath Tub
How to Remove and Also Replace a Bath Tub
Blog Article
Were you trying to locate resources about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Setting up a tub isn't specifically brain surgery, yet it does need solid plumbing, woodworking, and also in some cases, tiling skills. Changing an old bathtub with a new one is additionally a moderately tough project. If the old bathtub is readily easily accessible, the job can move immediately; if you have to open a wall surface to eliminate the old bathtub as well as place the new bath tub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly need an assistant to move out the old tub and also set in the brand-new one. Make sure you have certified yourself for the task and also are comfortable trying it. Rather than employing a service provider to take over a halfway-completed task, it is better to think about utilizing one prior to you begin. Possibilities are you might need an expert plumber to make tube links.
This article will aid you install a new bath tub in your bathroom if you have currently acquired a new tub and also do not need to alter the setup of your previous water supply pipes.
Your tools as well as product checklist ought to make up the following:
Getting ready for the Setup
To start with, the sustaining structure supplied with the bath ought to be fitted (if needed) according to the supplier's instructions. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is essential to make sure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally practical to fit a supporting plate under the taps system to prevent strain on the bathtub.
Fit the flexible tap connectors to the bottom of both faucets making use of 2 nuts and also olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you utilize all of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to currently prepare to be fitted in its last placement.
Removing Old Touches
If you require to replace old taps with new ones as a part of your installment, after that the first thing you must do is detach the supply of water. After doing so, turn on the taps to drain pipes any kind of water staying in the system. The process of removing the existing faucets can be fairly troublesome due to the limited accessibility that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the taps. Have a cloth all set for the staying water that will originate from the pipelines. Once the supply pipelines have actually been removed, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from turning throughout this procedure. Once the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any kind of old securing substance.
Before going on to fit the brand-new taps, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Setting up the Bath tub
Utilizing the two wood boards under its feet, put the bath tub in the needed position. The wood boards are useful in equally spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four little points.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by checking the level and changing the feet on the bathtub up until the spirit level checks out degree.
To set up faucets, fit the bottom of the outermost flexible faucet connector to the proper supply pipe by making a compression join; after that do the exact same for the various other tap.
Turn on the water supply as well as examine all joints and brand-new pipework for leaks as well as tighten them if essential. Fill the bath tub and likewise examine the overflow outlet as well as the regular outlet for leakages.
Ultimately, repair the bathroom paneling as described in the producer's user's manual. Tiling and securing around the bathtub ought to wait till the bathtub has been utilized at the very least once as this will certainly resolve it into its final setting.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will need a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and also the other end offers a link to the current supply pipes.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin ensuring that the washers are in location in between the faucet and also the sink. Secure the tap in place with the producer supplied backnut. As soon as the faucet is firmly in position, the supply pipes can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical faucet adapters. The previous kind needs to be attached to the faucet finishes first, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to crack a rigid seal, causing the water to pass through the wall surface between the bath and the tiling, leading to difficulties with wetness as well as possible leaks to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your components as well as fittings. They are sold in tubes and also cartridges, as well as are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to constantly fill up the bathtub with water prior to securing, to permit the motion experienced when the tub remains in use. The sealant can split relatively early if you do not think about this motion before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily readily available on the market. It is advisable to fit the ceramic tiles using waterproof or water resistant adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I stumbled upon that post about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when doing research the search engines. Do you know about someone else who is in to the topic? Please feel free to promote it. Kudos for your time. Come back soon.
Browse Our Site
Report this page